NEW Solder Slug Pellets With Flux Core For Copper Battery Cable Ends & Lugs

• Popularity - 41185 views, 5883.6 views per day, 7 days on eBay. Super high amount of views. 3759 sold.
• Price - Avg: $0.00, Low: $0.00, High: $0.00. Best quality when compared to PicClick similar items.
• Seller - + items sold. 0% negative feedback. Great seller with very good positive feedback and over 50 ratings.

Solder Slug Pellets with Flux Core<br>for Battery Terminals, Lugs, and other Copper Cable Ends<br>These solder pellets provide maximum conductivity and a corrosion-proof seal. The result is a high quality termination without the need for expensive crimping tools. The pre-measured amount of solder is color coded to match industry standard wire size identification colors. The flux core prevents dirt and contaminants from interfering with the soldering process.<br>We also have the<br>CL-Flux<br>which is recommended to aid in the cable soldering available in our store as well. A few drops on the cable strands before inserting into the melted solder really help the solder to flow around the strands and form a nice bond.<br>You have a choice of sizes and quantity so you can get what you need or create your own assortment.<br>Shipping:<br>We combine shipping! Add all items to the cart and after you have all the items you need you THEN proceed to the checkout so the order can combine into a single order. We combine shipping so we make it easy for you to get what you need.<br>Be sure to check our store and other items for battery cable ends such as top post terminals and lugs (closed end ring terminals).<br>Other Features and Benefits:<br>Color-coded solder pellets conform to industry standards & ensure correct product identification.<br>Pre-measured solder pellets assure the right amount of solder will be used in each connection.<br>Flux core and No-Clean liquid flux (<br>CL-Flux<br>available in our store) prevent dirt and contaminants from hindering the soldering process.<br>Can be installed using only a standard propane shop torch and a utility knife<br>No need to purchase an expensive crimping tool<br>Requires no special connectors<br>Works with any brand of closed-end battery terminals or starter lugs<br>Use with your current inventory - no need to purchase special ?Solder-Only? connectors<br>The least expensive method of obtaining a high quality soldered and sealed connection<br>INSTALLATION INSTRUCTIONS<br>1. Using the proper sized cable, measure the amount of insulation to be stripped by placing the cable next to the<br>length of the barrel. Mark the cable with your thumb at the point where it meets the end of the open barrel.<br>2. Strip the cable using a cable stripping device. After removing the insulation, check by inserting the cable<br>into the barrel to make sure the insulation is snug against the top of the barrel.<br>3. Next, secure the battery terminal in a vise. Make sure that the offset portion of the barrel is facing you.<br>4. Place the proper solder pellet into the barrel of the terminal.<br>5. Slide the heat shrinkable tubing over the cable.<br>6. Apply several drops of the liquid flux to the exposed wire strands.<br>7. Pre-heat the solder and terminal with a propane torch according to the Preheating Time Table.<br>Make sure that you are heating the offset portion of the terminal barrel.<br>8. After pre-heating, carefully insert the exposed cable into the barrel of the terminal and continue to heat.<br>9. As the solder melts, allow the exposed wire strands to sink into the terminal until the insulation is snug<br>against the top of the barrel.<br>10. Slide the heat shrinkable tubing over the connection and apply indirect heat to the tubing.<br>11. When the tubing has fully recovered, remove the heat source and allow the connection to cool.<br>Preheating Time Table<br>Part#    Time(sec)<br>CL-6       0:06<br>CL-4       0:06<br>CL-2       0:09<br>CL-1       0:15<br>CL-0       0:11<br>CL-00     0:13<br>CL-000   0:15<br>CL-0000 0:30<br>